Target: O3
Model: MQ131-H
Detection range: 10-1000ppm
Detection principle: Semiconductor
Characteristics: Good sensitivity to O3
Size: φ19×24.2
Working conditions: Loop Voltage:5±0.1V
Heater Voltage:5±0.1V
Heater consumption:≤950mW
Notes: High concentration

MQ131-H Manual download
Get Price Whatsapp

Description

Sensitive material of MQ131 gas sensor is semiconductor metallic oxide, which with high conductivity in clean air. When the ozone gas exists, the sensor’s conductivity gets lower along with the gas concentration rising. Users can convert the change of conductivity to correspond output signal of gas concentration through a simple circuit.
MQ131 ozone gas sensor has high sensitivity to ozone and also has sensitivity to strong oxide gases, such as Cl2, and NO2 etc. It responses oppositely to organic interference gases, compared with O3.

Application

It is widely used in domestic ozone concentration alarm, industrial ozone concentration alarm and portable ozone concentration detector.

Features

It has good sensitivity to ozone in wide range, and has advantages such as long lifespan, low cost and simple drive circuit &etc.

Specifications

Model MQ131
Sensor Type Semiconductor
Standard Encapsulation Bakelite, Metal cap
Target Gas Ozone
Detection range 10~1000ppm Ozone
Standard Circuit Conditions Loop Voltage Vc 5.0V±0.1V DC
Heater Voltage VH 5.0V±0.1V AC or DC
Load resistance RL Adjustable
Sensor character under standard test conditions Heater Resistance RH 30Ω±3Ω (room temp.)
Heater consumption PH ≤950mW
Sensitivity S Rs(in 300ppm O3) / Rs(in air)≥2
Output Voltage △Vs ≥1.0V(in300ppm O3)
Concentration Slope α ≤0.6( R10ppm/R100ppm O3)
Standard test conditions Tem.  Humidity 20℃±2℃;55%±5%RH
Standard test circuit Vc:5.0V±0.1V; VH: 5.0V±0.1V
Preheat time Over 48 hours
Oxygen content 21% (not less than 18%, (oxygen concentration will affect the initial value, sensitivity and repeatability of the sensor, please consult when using it under low oxygen concentration)
Life span 5 years

* The description and specifications might be changed without notice. Please contact us for the latest information before placing orders.

Technical Support:

Customized technical design and function, LOGO and package are available without extra charge (including molding fee) for mass volume.

The sensors don't have sleeping mode. It can be set in program if needed.

All Winsen products go through strict inspections and tests to make sure they are 100% qualified before shipping out.

The sensor has been fully tested (not calibrated) before leaving the factory, but the module will be calibrated before leaving the factory.

However, after transportation and storage, the environment conditions change, and the surface of the sensor absorbs moisture, mixed gas, pollution matters, etc. It is recommended that customers perform aging and calibration after sensors become stable according to the program and use occasions of the whole device.

15﹪-90﹪RH without condensation,greater or less than this range or long-term high temperature and high humidity will affect the life of the sensor.

Our sensors are certified with CE, 3C, ROHS, anti-explosion, fire prevention, and coal mining safety according to different applications. And we provide assistance for new certification.

Many factors can cause the sensor to fail such as broken wires in transportation, poisoning, falling off of the sensitive material, damage to the heating wire (device), etc. Please find specific cause in each category with Winsen’s aftersales.

Winsen provides professional consultation and service before and after sales. We will recommend the best fitting sensor for your demand. If you have any problem, don’t hesitate to email us to sales@winsensor.com

Due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. But we will reply to your inquiry in 24 business hours.

LEADING GAS SENSING SOLUTION SUPPLIER

RELATED PRODUCTS